Mer-Ko Products
Weather deck
HOME PAGE
Mer-Ko Home Page
Waterproof Decking /
Below Grade
Urethane Decking /
Elastomeric Membranes
Underlayment Systems
Installation Detail Drawings
Material Safety Data
CSI Specifications
Request Information
Mer-Ko Catalog PDF Library
Search Our Site

 



>Specification
>CSI Specification
>"One Hour"
Assembly
>Detail-Tube Steel Rail
>Detail-Two Piece Flashing
>Listings, Approvals & Recommendations
>Color Selections

>MAINTENANCE AND RE-SEALING INSTRUCTIONS

>Catalog Pages (PDF Format)

 

Mer-Ko™ Weather Deck

WATERPROOF & FIRE RETARDANT PEDESTRIAN DECKING
Weatherdeck

DESCRIPTION:
Weather Deck is a multilayered latex mastic roofing system which is trowel applied to a “floating” base sheet.
This system provides a slip resistant, waterproof walking surface that is isolated from substrate cracks. Waterproof flashing for drains, vertical surfaces, thresholds, as well as stress relief for thermal expansion are incorporated into the system. The thickness is approximately 3/16"-1/4" (4.7 mm-6.35 mm) and presents few elevation problems at doors, landings, steps, etc.

USE:
Flat roof decks, observation decks and balconies on commercial and residential buildings carrying pedestrian traffic. (For vehicular traffic, refer to Mer-Ko AutoDeck).

APPROVALS:
Weather Deck has been approved as a Class A fire-retardant roofing system by:
• ICC-ES - Report No. 3389
• City of Los Angeles - RR 23811
• California State Fire Marshal

ADVANTAGES:
• Monolithic, contains no joints or seams.
• May be installed over any sound, solid, dry subsurface.
• Fire retardant-One Hour Fire Rated – See “One Hour” Assembly Addendum.
• Will not soften under extreme solar temperatures.
• Installed only by qualified applicators.

LIMITATIONS:
• Not designed for vehiclar or heavy steel wheeled traffic.
• Subsurface must be dry before and during application.
• In cold climates, consult manufacturer for specific requirements.
• Not for use over OSB board.

CONSIDERATIONS FOR INSTALLATION:
• Subsurface must be smooth. If not corrected, irregularities will reflect on the Weather Deck surface.
For example, if a quarry tile deck has irregular grout joints which are not smoothed with underlayment, the grid pattern will show on the Weather Deck surface.
• Minimum standards for wood surfaces are 5/8" exterior plywood over 16" o.c. joists or 1/2" exterior
grade plywood over sheathing.
• To insure perimeter flashng is installed per Mer-Ko specifications, please contact the Mer-Krete Systems/ Mer-Ko Materials a division of Parexlahabra office.
• In freezing climates, sufficient pitch is required to insure run-off. When covering a “sandwich
slab” or quarry tile deck, provision must be made to vent the envelope created between the
existing vapor barrier and the Weather Deck.

 

• Drains must be of a design suitable to receive Weather Deck flashing (i.e. J.R. Smith
DX-1240 series).
• Concrete subsurfaces must have a minimum compressive strength of 1000 psi tested by “point
loading” technique.
• The moisture content of the substrate should be checked and approved by authorized Mer-Ko
installer prior to installation.
• When contemplating a deck installation with an open soffit, or over an unheated enclosed space
(i.e. garage, etc.) in freezing, damp or severe climates, consult manufacturer for recommendations.

INSTALLATION:
1. Initial base sheet
2. Glassmat and synthetic burlap reinforced waterproof membrane
3. Two trowel applied coats of a highly flexible rubber mastic filler
4. A filler coat to smooth and provide a wearing surface
5. Two coats of high resin solids sealer in chosen color

 

Mer-Ko Deck Coverings
A ParexLahabra, Inc. Brand
501 Van Ness Avenue, Torrance, California 90501
(323) 775-2461 / FAX (310) 320-4938
E-mail: info@merkrete.com
(800) 851-6303

 

© 2007 ParexLahabra. All rights reserved.

Created by LTG&A, Inc